金屬薄板涂層要求翻譯-中英對照
在要求完全防水的各處都需要裝遮雨板。其鋼板的厚度應當不小于0.7毫米。套筒帶的周長應當在15厘米到25厘米之間。
在壁板、屋頂以及內墻的管道的穿插、套接、開口等應當在投標人的設計圖中展示出來，且應當合理設計，達到防風、防雨、防塵的效果。
天窗
天窗應當符合在一般技術規范的“金屬薄板”和“金屬薄板涂層”兩部分中提到的要求。其所用到的材料、扣件以及涂層應當與技術規范中所規定的壁板材料的規格相同。
4.4.3.23.9 裝配
轉配應當嚴格按照廠家的程序步驟來。金屬和鋁應當時刻分開以避免發生電鍍反應。
4.4.3.23.10 在裝配過程中隔熱材料的保護
對于所有隔熱的構筑，在裝配過程中保護其免受風吹日曬等天氣的變化損害，減少隔熱材料吸水或者吸收其他潮濕的東西。
4.4.3.23.11 壁板、屋頂和內墻的清潔
壁板、金屬屋頂和內墻的所有暴露在外的部分應當無標記、無灰塵、無污漬、無裂縫、無變色等。其在安裝的時候管道至少應當是干燥的。
壁板、金屬屋頂和內墻的所有暴露在外的部分，在業主驗收前其外觀首先應當令人滿意。
4.4.3.23.12 外觀存在缺陷的補救方法
外觀的缺陷包括缺口、抓痕、擦傷、凹陷、涂寫（handing）、erection、風化等。投標人對此的補救方法如下：
在原來的涂層上再次涂上一層或者多層相同材質的有機瓷釉進行修葺。修葺部分的厚度、外觀和色彩應當與原先的吻合。若修葺部分無法令業主滿意，則應當更換損壞的薄板或者零件。
4.4.3.23.13 檢查與檢測
除非另有規定，投標人應當負責本規范中提到的所有檢查和檢測。業主在檢查或者檢測過程中，可以到投標人的工廠或者施工地點察看投標人的工作進度。
涂層檢測
屋頂和墻面的外鋼板涂層應當符合下列標準，且試驗結果應當由中立的檢測機構證明，由其認可。
以下的各個檢測結果均應當提交給雇主，與以下要求進行核對。
色彩的變化和防止退色的性能
一個至少有兩個直接切下來的邊緣的樣本，經過至少60天的加速耐候性試驗和/或200.000蘭利的紫外線照射無破裂，起皮、起泡或脫落。最大的色彩變化，包括外部的污垢、塵土堆積，應當不超過每單位2nbs。
磨損——涂層的耐久性檢測
該試驗中采用扁平試樣。檢測主要是依據ASTM的D-968-51（）的試驗標準進行的，其中指出，末端最先顯示的是基底金屬。在這個檢測中，涂層在顯露極地金屬之前應需要能夠經受至少200次粗沙的摩擦。
涂層整體性檢測
根據ASTM B-117-64號的試驗標準，樣本至少需要在鹽霧試驗中經過1000個小時，還包括掛擦試驗。從試驗環境中移出來時，樣本應當沒有任何破裂、駁皮、起泡或者脫落。
耐污檢測
沒有任何保護邊緣的扁平試樣，將在克氏試驗中循環30個周期，要求樣本沒有任何破裂、駁皮、起泡或者脫落的現象出現�？耸显囼�(yàn)是首先將樣品暴露在40攝氏度的溫度下8小時，樣品會被放置在相對潮濕的SO2和CO2氣體環境中，兩種污染氣體的濃度根據克氏試驗的DIN50018號測試標準規定。隨后又是16個小時的干燥時間，這才完成一次克氏試驗的循環周期。
耐濕性測試
根據ASTM的D-2247-68號試驗標準，樣品要在華氏100度的溫度下放置1000個小時，要求樣本沒有任何破裂、駁皮、起泡或者脫落的現象出現。
鏡面光潔度測試
根據ASTM的D-2247-68號試驗標準，一個平面樣本會在60華氏度的溫度下進行測試，等級會在10到15之間。
漆膜硬度檢測（ASTM第D3363號標準），應當至少能夠經受住F鉛筆的推劃。
人工老化試驗（ASTM第G23號標準），在陽光射線下暴曬5000個小時，在8號的每次ASTM第D659試驗的時候沒有脫落現象，且每經過一次STM D224的試驗退色不會超過5nbs，在凝露循環試驗下循環60/60個周期。
可延展性測試（ASTM第D1737號標準）：能夠經受1T到2T的彎曲。
光滑度測試（ASTM第523號標準）：在60度的光澤度計上有25-35%的反射率。
撞擊：當如下測試結束后，涂層沒有脫落。
用一把鋒利的刀從涂層到金屬平行地刻下6道或者更多道口子，每條刻痕間隔1.5毫米。
以相同方式交叉刻。
保留影響為東92厘米/公斤，或者是對準金屬的裂縫。
用玻璃紙膠帶粘在刻痕上，然后猛力拉開。
應當沒有涂層掉下。
Flashings shall be provided where required to reach full water tightness. The thickness of steel shall not be less than 0.7 mm. Cap strips, if required shall have a girth comprised between 15 cm and 25 cm.
PENETRATIONS, WALL OR ROOF SLEEVES
Penetrations, sleeves, duct openings, etc, in siding, roofs, and interior walls shall be shown on Bidders drawings and shall be soundly designed for weather tightness.
LOUVERS
Louver shall comply with the requirement defined in the general technical specifications refers to sub section 'Metal Sheets' and 'Metal Sheet Finishes'. The Material, fasteners and finishing shall be the same as the siding material defined in this general technical specification.
4.4.3.23.9 ERECTION
Erection shall be in strict accordance with manufacturers' procedure for this type of work. Care shall be taken to insure that Metal and aluminium are at all times separated such that a galvanic reaction cannot take place.
4.4.3.23.10 PROTECTION OF INSULATION DURING ERECTION
For all insulated constructions, satisfactorily protect all insulation from the weather during erection so as to eliminate soaking of insulation by water, or other moisture contaminants.
4.4.3.23.11 CLEANING OF SIDING, ROOFS AND INTERIOR WALLS
All exposed faces of siding, metal roofs and interior walls shall be cleaned of labels, dirt, streaks, caulking or sealing materials, undue discoloration etc. and as a minimum a dry wipe down shall be provided at the time of erection.
All exposed faces of siding, metal roofs and interior walls, prior to acceptance by Owner shall be completely satisfactory to the Owner in appearance.
4.4.3.23.12 REMEDY OF DEFECTS IN APPEARANCE
Defects in appearance shall include nicking, scratching, gouging, dimpling, denting, abrasions, and marring of any nature due to shipping, storing, handling, erection, weathering etc. and shall be remedied at Bidders expense as follows:
0310293
Revision 0 ~~™~~ Part 4.4-266 PLTU Adipala (PLTU 2 Jawa Tengah)
1 x (600-700 MW) Location Cilacap
BOOK III
PART 4.4 Civil Works 4.4.3 Technical Specification
Touch up the baked enamel organic coating finish with one or more coats of the same coating material used for the original finish. Thickness, appearance and colour of the touch-up shall match adjacent surfaces. If touch-up is not satisfactory to Owner, damaged sheets or accessories shall be replaced.
4.4.3.23.13 INSPECTION AND TESTING
The Bidder shall be responsible for all inspection and testing required by this specification unless otherwise specified. The Owner may during the course of the work, observe various phases of the work performed by Bidder, at the Bidders plant and at the site.
Coating Tests General
The coating system of the external steel sheet for roof and wall has to meet the following performance criteria and test results and must be substantiated and certified by a recognized independent testing organization.
Result of following tests shall be submitted to the Employer, proving the compliance with the following requirements.
Colour Change and Fade Resistance
A sample with a minimum of two raw-cut edges shall withstand a minimum of 60 days emmaqua weathering test exposure (exterior equatorial mount with mirrors and water spray) and/or 200.000 Langley's of ultra violet radiation without cracking, peeling, blistering or loss of adhesion. Maximum colour change, including all exterior surface deposits such as dirt or chalk, shall not exceed 2 nbs units.
Abrasion - Resistance Test for Coating System
A flat specimen shall be subject to abrasion-resistance test. Test shall be conducted in accordance with ASTM D-968-51 (falling sand) which specifies that the end point shall be the first appearance of the base metal. Coating system shall resist abrasion to the extent indicated by the use of not less than 200 litters of sand to procedure a first appearance of base metal.
Coating System Integrity Test
A sample shall withstand a salt-fog test for a minimum of 1.000 hours in accordance with ASTM B-117-64, including the scribe requirement in the test. Immediately upon removal of the specimen from the test, the coating system shall show no signs of cracking, peeling, blistering or loss of adhesion.
C3KJ294
Revision 0 Part 4.4 - 267 PLTU Adipala (PLTU 2 Jawa Tengah)
1 x (600-700 MW) Location Cilacap
BOOK III
PART 4.4 Civil Works 4.4.3 Technical Specification
Pollution-Resistance Test
A flat specimen, with no protected edge, shall be subjected to the 30 cycles of Kesternich testing without blistering, peeling or any other of joss of adhesion. The Kesternich test consist of eight hours of exposures at 40
With 100% relative humidity (condension) in a controlled sulphur dioxide (SO2), carbon dioxide (CO2) atmosphere. Atmospheric concentrations of pullutant gases shall be in accordance with Kesternich test standards DIN 50018. This is followed by 16 hours of dry time, which concludes one cycle of testing.
Humidity-Resistance Test
A sample shall be tested for 1000 hours at 100 deg F in accordance with ASTM D - 2247 - 68 with no blistering, peeling or loss adhesion.
Glare-Resistance Test
A flat sample shall be tested at 60 deg in accordance with ASTM D - 523 - 67. The rating shall fall in the 10 to 15 range.
Pencil Hardness (ASTM D3363) : Shall be F minimum
Weatherometer (ASTM G23) after 5000 hours exposure in sunshine Arc. Weatherometer or Atlas Twin Arc Weatherometer, no chalk in excess of No. 8 per ASTM D 659 and no colour fade more than 5 NBS units perSTM D2244, as operated under Dew Cycle conditions using 60/60 cycle.
Flexibility (ASTM D 1737) : Withstand 1T - 2T bends
Gloss (ASTM D 523) : 25-35 % reflectivity measured on 60 °C gloss meter.
Impact : no removal of finish when tested as follows :
Using as sharp knife, make 6 or more parallel cuts at 1.5 mm intervals through finish to bare metal.
Cross hatch similarly.
Reserve impact to east 92 cm - kg or to point of metal rupture.
Apply Scotch cellophane tape firmly to scribe impacted are. Remove tape with sharp pull.
There shall be no loss of adhesion.
2013.5.7